Wr flywheel on aby

martinws · 18-06-11, 07:44 PM

I'm about to fit a wr flywheel and clutch to an aby. I think this is an obvious question but when I'm at TDC is the timing pin on flywheel infront of the crank sensor?

Cheers

Tonks4x4 · 18-06-11, 09:39 PM

No it is not....

The flywheel will only actually bolt o. In one position anyway so you can't get it in the wrong position.

Look for the 0 on the flywheel rim that will indicate TDC once the gearbox is fitted you can see half of it through the viewing window

Isimmo · 18-06-11, 09:45 PM

Quote:

Originally Posted by Tonks4x4

No it is not....

The flywheel will only actually bolt o. In one position anyway so you can't get it in the wrong position.

Look for the 0 on the flywheel rim that will indicate TDC once the gearbox is fitted you can see half of it through the viewing window

As above, pick your clutch and power output carefully though....

martinws · 18-06-11, 09:48 PM

Nice on tonks.I was just sitting watching tv and it suddenly popped onto my head, I changed front crank seal,water pump etc today and was going on to the rest in the morning.

Tonks4x4 · 18-06-11, 09:49 PM

Should be running tomorrow night then

BIGGYIN · 18-06-11, 09:50 PM

martinws · 18-06-11, 10:07 PM

That will be the day.haha. The mechanical side doesn't bother me, just the wiring.
Isimmo- iv got a new wr clutch to use, Engine is staying standard for now.

Isimmo · 18-06-11, 10:21 PM

Quote:

Originally Posted by martinws

That will be the day.haha. The mechanical side doesn't bother me, just the wiring.
Isimmo- iv got a new wr clutch to use, Engine is staying standard for now.

That'll be good... we are running circa 300bhp on an uprated WR clutch with the AAN and I'm told that's about all it'll take + or - ... Certainly not had any problems so far, but I'm relatively gentle with it, although....

It does get a little abuse occasionally....

martinws · 19-06-11, 04:54 PM

Just fitted timing belt with new pulleys, rear crank seal, pressed bearing into rear of crank and put on the flywheel. I see what you mean by all the holes only lining up in one position. Dinner then ill move onto the clutch.

18-06-11, 09:39 PM	#2
Tonks4x4 4 ring whore! Classic Audi Club Member Join Date: Oct 2008 Location: Huthwaite, Nottinghamshire Posts: 2,607	Wr flywheel on aby No it is not.... The flywheel will only actually bolt o. In one position anyway so you can't get it in the wrong position. Look for the 0 on the flywheel rim that will indicate TDC once the gearbox is fitted you can see half of it through the viewing window __________________ http://www.tonks4x4.com

18-06-11, 09:49 PM	#5
Tonks4x4 4 ring whore! Classic Audi Club Member Join Date: Oct 2008 Location: Huthwaite, Nottinghamshire Posts: 2,607	Wr flywheel on aby Should be running tomorrow night then __________________ http://www.tonks4x4.com

18-06-11, 09:50 PM	#6
BIGGYIN 4 ring whore! Classic Audi Club Member Join Date: Mar 2009 Location: Merseyside Posts: 7,976	__________________ q90 B2 Type 85 - q90 B2 Type 85-PROJECT-ABY 20vt KARL. Injection is nice but I'd rather be blown

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

18-06-11, 09:48 PM	#4
martinws Grown up member Classic Audi Club Member Join Date: Sep 2009 Location: Johnstone Posts: 723	Nice on tonks.I was just sitting watching tv and it suddenly popped onto my head, I changed front crank seal,water pump etc today and was going on to the rest in the morning.

18-06-11, 10:07 PM	#7
martinws Grown up member Classic Audi Club Member Join Date: Sep 2009 Location: Johnstone Posts: 723	That will be the day.haha. The mechanical side doesn't bother me, just the wiring. Isimmo- iv got a new wr clutch to use, Engine is staying standard for now.

19-06-11, 04:54 PM	#9
martinws Grown up member Classic Audi Club Member Join Date: Sep 2009 Location: Johnstone Posts: 723	Just fitted timing belt with new pulleys, rear crank seal, pressed bearing into rear of crank and put on the flywheel. I see what you mean by all the holes only lining up in one position. Dinner then ill move onto the clutch.